8 Easy Ways to Remove Dents Yourself Without Ruining the Paint
« Auto Maintenance & Repairs :: WonderHowTo
Only three things in life are certain: death, taxes, and getting a dent in your car or truck. Even if you’re as careful as possible, you can’t always account for runaway shopping carts, wrongly thrown footballs, out-of-nowhere light posts, and other real-life annoyances.
However, not all of these tricks will work on your particular automobile; your mileage may vary depending on where the dent is and what your body panel, hood, or bumper is made of (aluminum, carbon fiber, plastic, fiberglass, steel, etc.). For instance, aluminum has little memory properties, so paintless dent removal is much more difficult.
Not only can you unclog a drain with a plunger, but you can also get small- to medium-sized dents out of your car too. Just splash some water on both the plunger and the dent and start pushing and pulling until it pops out. Make sure to use a cup plunger (for sinks), not a flange one (for toilets).
Reversing into an object is one of the easiest ways to get a dent. So for plastic bumpers, even if you attempt to take off the bumper, it might still be difficult to push out the dent because of how stiff the plastic is. Solve this issue by boiling some water in a pot and throwing it on the dent.
As soon as you’ve poured the water, reach behind the bumper and try to pop the dent back in. Thanks to the heat of the water, the plastic should be a bit more flexible, making it easier to put back into place.
Since the heat won’t last very long, you’ll have to work quickly. If the dent doesn’t completely go out, keep dumping boiling water on it until you’ve popped it all the way back out.
Another popular method for removing car dents out of plastic material involves using two popular household products: a hair dryer and compressed air.
Start off by heating the car dent with the hair dryer at its highest temperature, which will expand the plastic of the car. As soon as it’s hot enough, grab the can of compressed air, turn it upside down, and begin spraying that same area. Since the cold air will cause the plastic to contract, the dent will pop out.
Primarily used as a cooling agent, dry ice can be used to get out small dents from your car. As long as you’re wearing protective gloves, hold down a piece of dry ice on the dent and rub it around until you hear your dent pop back into place.
Apply the dry ice as many times as you need to, but it should pop out eventually if the dent isn’t too deep. You can also try heating up the dent first, with something like a hair dryer (similar to the hairdryer and compressed air tip above), and then apply the dry ice to it.
Suction is one way to get out a dent, but the problem is finding a dent puller with the right amount of power. Well, why not just create your own? All you need is a pot (or bucket), a vacuum cleaner and some tape and you can get that dent out of your car in no time.
Simply make a small hole underneath the pot, tape the pot around the dent, place the vacuum cleaner hose over the hole under the pot, and turn on your vacuum. If the dent isn’t too shallow, the suction created should pop out your dent.
When you attempt to take out dents yourself, you always put the risk that you might further damage your car, whether you make the dent worse or chip the paint. A safe way of trying to take out big dents on your car is by using several wooden dowels, a few screws, and a hot glue gun.
Simply place two nails into each side of the dowel and put the hot glue on the bottom. Place the dowels glue-side down in areas around the dent, repeat as many times as needed to cover the area, let them dry, and pull each one out until the dent is gone.
Place and pull the same dowels in several different places across the dent until most of it comes out. If you’re going to try this method, make sure that you have enough glue and some patience. Use rubbing alcohol or heat to detach the glue from the car.
When a dent happens on your car, the metal not only goes inward, the surrounding edges of the dent also go upward, creating something like a small volcano. That means that popping the dent out from underneath is not the way to go.
George Gjokaj, a master Paintless Dent Repair (PDR) technician, fixes dents by going to work on both sides of the dent. By using a combination of a long metal rod underneath it and a knockdown or tap-down tool (wooden or rubber) on the top side, he can completely get the dent out of the car. And boy, does it work.
If you’re willing to try anything and don’t have a ton of tools at home, grab a dent removal kit, which contains tools specially created to remove car dents using many of the methods detailed above.
Did you give any of these methods a try, or did you end up biting the bullet and hiring an auto body shop to do the work for you? If you used a different DIY method for removing dents and dings from your vehicle, make sure to let us know below!